Mercedes Atego 2 List of control codes for level control (NR).(MTCO)

0160 CAN bus IES: CAN bus off

0161 CAN bus IES: disconnection

0162 CAN bus IES: no speed signal (FR and ABS / BS).

0163 CAN bus IES: no signal 'service brake system' (FR).

0164 CAN bus IES: no signal 'Engine speed' (FR).

0165 IES-CAN: Signal 'No residual pressure in circuit 1 * (INS).

0166 IES-CAN: Signal 'No residual pressure in circuit 2 ’' (INS).

0167 CAN bus IES: no signal 'Supply voltage, bit information' (INS).

0168 CAN bus IES: no signal 'Supply voltage, byte information' (INS).

0169 CAN bus IES: no corner detection

0170 CAN bus IES: No set brake pressure.

0171 CAN bus IES: no corner detection possible

1010 Internal error in the control unit

1012 Control unit: checksum for specific ECU data

1013 Control unit: parameter checksum

1014 Incorrect checksum of calibration data of displacement sensors.

1015 Incorrect checksum of calibration data for pressure sensors.

1016 Incorrect checksum for axle load calibration data.

1017 Incorrect checksum on axle loads.

1101 Overvoltage at terminal 30

1102 Undervoltage at terminal 30

1301 Overvoltage at terminal 15

1302 Undervoltage at terminal 15

1303 Terminal 15: out of actual voltage range

2030 Control panel, data, circuit break

2031 Control panel, data, short circuit to ground

2032 Control Panel, data, short circuit to positive

2130 Control panel, clock, circuit break

2131 Control panel, clock, short to ground

2132 Control panel, clock, short circuit to plus

2230 Control Panel + UB, electrical circuit break

2231 Control Panel + UB, Short to Ground

2232 Control Panel + UB, short to positive

3020 Solenoid valve 3/2, filling, circuit break

3021 Solenoid valve 3/2, filling, short circuit to ground

3022 Solenoid valve 3/2, filling, short circuit to positive

3120 Solenoid valve 2/2, drive axle left, open circuit

3121 Solenoid valve 2/2, drive axle left, short to ground

3122 Solenoid valve 2/2, drive axle left, short to positive

3220 Solenoid valve 2/2, drive axle on the right, open circuit

3221 Solenoid valve 2/2, drive axle on the right, short to ground

3222 Solenoid valve 2/2, drive axle on the right, short circuit to positive

3320 Solenoid valve 3/3, lowering 3. bridges, breaking the electrical circuit

3321 Solenoid valve 3/3, lowering 3. bridge, short to ground

3322 Solenoid valve 3/3, lowering 3. bridge, short to positive

3420 Solenoid valve 3/3, lifting 3. the bridge, breaking the electrical circuit

3421 Solenoid valve 3/3, lifting 3. the bridge, short circuit to ground

3422 Solenoid valve 3/3, lifting 3. of the bridge, short circuit to positive

3520 Solenoid valve 2/2, front axle, open circuit

3521 Solenoid valve 2/2, front axle, short to ground

3522 Solenoid valve 2/2, front axle, short to positive

3620 Solenoid valve return, open circuit

3621 Solenoid return valve, short to ground

3622 Solenoid return valve, short to positive

4040 Travel Sensor, drive axle left, circuit break

4041 Travel Sensor, drive axle left, short to ground

4042 Travel Sensor, drive axle left, short to positive

4043 Left drive axle displacement sensor: coil nominal resistance fault

4140 Travel Sensor, drive axle on the right, circuit break

4141 Travel Sensor, drive axle on the right, short to ground

4142 Travel Sensor, drive axle right, short to positive

4143 Right drive axle displacement sensor: coil nominal resistance fault

4240 Travel Sensor, drive axle, circuit break

4241 Travel Sensor, drive axle, short to ground

4242 Travel Sensor, drive axle, short to positive

4243 Front axle displacement sensor: coil nominal resistance fault

5040 Pressure Sensor, drive axle left, circuit break

5041 Pressure sensor, drive axle left, short to ground

5042 Pressure sensor, drive axle left, short to positive

5140 Pressure Sensor, drive axle on the right, circuit break

5141 Pressure sensor, drive axle on the right, short circuit to ground

5142 Pressure sensor, drive axle on the right, short circuit to positive

5240 Pressure Sensor, drive axle, circuit break

5241 Pressure Sensor, drive axle, short to ground

5242 Pressure Sensor, drive axle, short to positive

5340 Pressure sensor + UB, open circuit

5341 Pressure sensor + UB, short to ground

5342 Pressure sensor + UB, short to positive

6020 The lead wire to the front axle proportional valve VUR has an open circuit.

6021 Lead wire to front axle proportional valve WR has a short to ground.

6022 The lead wire to the front axle proportional valve WR has a short to positive.

6023 The set current is not reached on the proportional valve WR of the front axle.

6120 The lead wire to the proportional valve WR 1. of the bridge has an open circuit.

6121 The lead wire to the proportional valve WR 1. of the rear axle has a short to ground.

6122 Lead wire to proportional valve \ A / R 1. The rear axle has a short to positive.

6123 The rated current at the proportional valve WR of the 1st rear axle is not reached.

6220 The lead wire to the proportional valve WR 2. of the bridge has an open circuit.

6221 The lead wire to the proportional valve WR 2. of the rear axle has a short to ground.

6222 Lead wire to rear axle proportional valve VUR 2. has a short to positive.

6223 The rated current at the proportional valve WR of the 2nd rear axle is not reached.

6320 Check valve WR has an open circuit.

6321 Check valve WR has a short to ground.

6322 Check valve WR has a short to positive.

0000 Tachogram positioning violated.

0004 Power failure

1000 CAN fault

1100 CAN fault

1200 Internal error

1400 Tachograph calibration is incorrect.

1500 Malfunction in the control panel

1600 Malfunction in the control panel

1704 CAN to INS (instrument cluster) connection defective

3408 Speed sensor malfunction

3504 Speed sensor malfunction

4804 Speed output failure

8000 Ride without a tachogram

8100 Driver 1 tachogram missing.

8200 Tachogram driver 2 is missing.

8300 Synchronization could not be started.

9000 Tachogram positioning violated.

9600 The operation of the pull-out compartment is disturbed.

9700 Speed Registration Failure

9800 Malfunction in the recording system

9900 Malfunction in the recording system

TYPE 375.1 with a body 375.850

TYPE 970, 972, 974, 975, 976 with the body 972.890

TYPE 958.0

0160 CAN bus disabled (OFF)

0161 Communication failure with FR control unit (motion control)

0167 Communication failure with control unit RS (retarder control)

0168 Communication failure with ABS control unit

0169 Communication failure with INS control unit (instrument cluster)

0171 Communication failure with control unit AG (automatic switching)

0172 Data transfer to CAN vehicle has been interrupted.

0173 CAN bus gearbox in single-wire mode

0174 CAN bus gearbox does not output data.

0176 CAN message failure 'Rated clutch release bearing adjustment spin value'

0177 CAN message 'Transmission Elements Reliable'

0361 Failure of the replacement motion function

0901 Overvoltage at terminal 30-2

0902 Undervoltage at terminal 30-2

0920 Undervoltage at terminal 30-2

1001 The power supply voltage of the travel sensors has an increased power supply.

1002 The power supply voltage of the travel sensors has a reduced power supply.

1010 Internal control unit malfunction

1011 A checksum error occurred while reading the EEPROM.

1012 A checksum error occurred while reading the EEPROM.

1015 A checksum error occurred while reading the EEPROM.

1016 A checksum error occurred while reading the EEPROM.

1097 The software in the control unit is a test version.

1098 The control unit is a test version.

1099 Active control unit mode for testing on a test bench.

1101 Overvoltage at terminal 30-1

1102 Undervoltage at terminal 30-1

1120 Undervoltage at terminal 30-1

1220 Solenoid valve ground wire has an open circuit.

1301 Overvoltage at terminal 15

1302 Undervoltage at terminal 15

1420 The voltage supply to the speed sensor has an open circuit.

1421 The voltage supply to the speed sensor has a short to ground.

1422 The voltage supply to the speed sensor has a short to positive.

1520 The pressure sensor has an open circuit.

1521 The pressure sensor assembly has a short to ground.

1522 The pressure sensor assembly has a short to positive.

1720 The temperature sensor of the output stage of the hydraulic pump has a short circuit to plus or open circuit.

1721 The temperature sensor of the output stage of the hydraulic pump has a short to ground.

1723 The output stage of the hydraulic pump is overheated.

1820 The voltage of valve relay 1 cannot be activated.

1821 The voltage of valve relay 1 cannot be deactivated.

1920 The voltage of valve 2 relay cannot be tripped.

1921 The voltage of valve 2 relay cannot be deactivated.

2020 High voltage power wire has an open circuit.

3020 Solenoid valve A92u1 has a short circuit to positive or open circuit.

3021 Solenoid valve A92u1 has a short to ground.

3120 Solenoid valve A92u2 has a short circuit to positive or open circuit.

3121 Solenoid valve A92u2 has a short to ground.

3220 Solenoid valve A92uZ has a short circuit to positive or open circuit.

3221 Solenoid valve A92uZ has a short to ground.

3320 Solenoid valve A92u4 has a short circuit to positive or open circuit.

3321 Solenoid valve A92u4 has a short to ground.

3420 Solenoid valve A92u5 has a short circuit to positive or open circuit.

3421 Solenoid valve A92u5 has a short to ground.

3520 Solenoid valve A92u6 has a short circuit to positive or open circuit.

3521 Solenoid valve A92u6 has a short to ground.

3620 Solenoid valve A92u7 has a short circuit to positive or open circuit.

3621 Solenoid valve A92u7 has a short to ground.

3720 Solenoid valve A92u8 has a short circuit to positive or open circuit.

3721 Solenoid valve A92u8 has a short to ground.

3820 Solenoid valve A92u9 has a short circuit to positive or open circuit.

3821 Solenoid valve A92u9 has a short to ground.

4120 The Transmission Sensor (SGG) has an open circuit.

4121 Transmission Sensor (SGG) has a short to ground.

4122 Transmit Sensor (SGG) has a short to positive.

4143 Malfunction of the Transmitter Transmitter Assembly (SGG)

4144 Transmit Sensor Transmitter (SGG) Out of Range

4220 Sensor 'transmission line * (SGE) has an open circuit.

4221 The 'transmission line' (SGE) sensor has a short to ground.

4222 The 'transmission line' (SGE) sensor has a short to positive.

4243 Malfunction of the "Sensor 'transmission line" 1 (SGE)

4244 Transmission Line Sensor 1 assembly (SGE) out of range

4420 The Clutch Sensor (SKU) has an open circuit.

4421 Clutch Sensor (SKU) has a short to ground.

4422 Clutch Sensor (SKU) has a short to positive.

4443 Malfunction of the "Sensor 'clutch'" (SKU)

4444 Clutch sensor assembly (SKU) out of range

5020 There is no signal from the speed sensor B113.

5096 The signal of the speed sensor B113 is broken

5120 There is no signal from the RPM sensor.

5121 The rotational speed sensor VZ 'intermediate shaft' has a short to ground.

5122 The OT 'intermediate shaft' speed sensor has a short to positive or an open circuit.

5196 Disrupted RPM sensor

5220 No speed signal.

5296 The speed signal is broken.

5320 The signal from the speed sensor V113.1 is missing.

5396 The signal of the speed sensor B113.1 is broken

6020 The output or lead wire of the output stage of the hydraulic pump has an open circuit.

6021 The output or lead wire of the output stage of the hydraulic pump has a short to ground.

8090 Reliability error of the actual transfer gearbox ratio

8091 No output speed of the gearbox

8093 Wrong gearbox type

8094 A certain direction of travel is unreliable.

8095 Unit pressure build-up too slow at system startup

8110 Reliability error of nominal value 'Adjustment of clutch release bearing'

8117 Reliability error of the nominal value of 'Adaptation value of clutch Minimum'

8185 Clutch position adjustment malfunction

8186 Reliability error due to clutch disengagement

8187 Validation error due to clutch engagement

8189 Reliability error of the nominal value 'Clutch stroke value'